Cellulose, as a fully renewable, biodegradable, and biocompatible material, creates new possibilities for optical fiber (OF) sensor applications. Cellulose OFs are highly hygroscopic, exhibiting rapid wetting and drying properties with water and moisture, easily functionalized, and can be either made water-resistant or water-soluble. These fibers are not aimed towards replacing the existing glass or polymer OFs in telecommunication or in current sensing applications, rather cellulose OF sensors can open new application areas where the reactive materials are required. For example, compared to glass or polymer OFs, cellulose OFs are porous and allow liquid transport in and out of the fiber. Moreover, the cellulose waveguide material itself can be chemically functionalized. Such cellulose OFs fit well with human health monitoring where the new possibilities that cellulose offers can be utilized. Here we demonstrate a face mask that contains regenerated cellulose (RC) OF with a 1.8 dB/cm attenuation constant for respiratory rate monitoring. RC is a class of man-made cellulose materials that includes commonly materials like rayon textiles and cellophane films. The cellulose fiber inside the face mask rapidly absorbs moist and dries between each breath, which causes a periodic change in optical power transmitted through the fiber. A face mask does not prevent fast drying of the fiber. Such RC fiber fits well to respiratory rate monitoring because it exhibits good mechanical performance in both dry and wet states. Cellulose OF length was about 5 cm long with a loop-type sensor structure. Measured respiratory rates varied between 16-54 breaths per minute.
We have designed and fabricated micro-LiDAR chips based on 1D optical phased arrays (OPAs) that collimate light in the horizontal direction only. Thus, a cylindrical lens is needed for the vertical collimation. A part of the work demonstrates the analysis of 1D beam steering experiments through the direct outcoupling from the waveguide facets with two straight cylindrical lenses available commercially and a detailed analysis based on the parameters like Rayleigh range and beam divergence is presented. This work also demonstrates the characterizations of 3D printed curved cylindrical collimating lenses. A thorough analysis based on the experimental work resulted in certain suggestions to improve the collimation and to perform the beam steering in a better way.
Cellulose materials offer new biodegradable alternatives for fabricating optical fibers for sensing applications. Unlike glass and polymer optical fibers, these environmentally friendly materials have intrinsic properties making them attractive candidates for functional optical fibers. Cellulose fibers are hygroscopic and thus can rapidly take water vapors from the surroundings and dry quickly. Cellulose-based optical fibers can be manufactured from regenerated cellulose or cellulose derivatives which offer a large property space. They can be resistant or soluble in water, and the refracting index of the material can be tuned as needed. In this work, feasibility for sensor applications of three different cellulose optical fibers have been tested: regenerated cellulose for water and humidity sensing, carboxymethyl cellulose for respiratory rate monitoring, and methylcellulose for short-range 150 Mbit/s signal transmission at 1310 nm. Therefore, fast signal transmission can be achieved with short cellulose-based sensor fibers. The work shows the scientific and technical potential of a novel optical material for photonics.
This paper explains and demonstrates the unique properties of micron-size silicon-on-insulator (SOI) waveguides. It gives an overview of the silicon photonics research at VTT, as well as latest R&D highlights. The benefits of high mode confinement in rib and strip waveguides are described, reaching from low losses and small footprint to polarization independent operation and ultra-wide wavelength range from 1.2 to over 4 μm. Most of the results are from photonic integrated circuits (PICs) on 3 μm SOI, while a 25 Gbps link with a transceiver on 12 μm SOI is also reported. Wavelength multiplexing and filtering is demonstrated with some breakthrough performance in both echelle gratings and arrayed waveguide gratings. Lowest losses are below 1 dB and lowest cross-talk is below -35 dB. Progress towards monolithically integrated, broadband isolators is described, involving polarization splitters, reciprocal polarization rotators and nonreciprocal Faraday rotation in 3 μm SOI waveguide spirals. Quick update is presented about switches, modulators and Ge photodiodes up to 15 GHz bandwidth. Hybrid integration of lasers, modulators and photodiodes is also reported. The added value of trimmed SOI wafers and cavity-SOI wafers in Si photonics processing is addressed. Latest results also include up-reflecting mirrors with <0.5 dB loss, which support wafer-level testing and packaging.
Diffraction gratings were designed and fabricated on a SiN/SiO2 planar waveguide to couple light from a low power 488 nm
laser beam into the planar waveguide. The light propagating in the waveguide was then used to detect fluoresceine from
volume on the planar waveguide surface. The results demonstrate the capability for very simple and fast analytical
throughput for quantification of fluorescent samples, essentially without cross-talk. The transmission measurements show
about 10% diffraction efficiency with 0.06° FWHM. The diffraction efficiency and the incidence angle for the maximum
diffraction efficiency were observed to be highly dependent on the process parameters used to fabricate the gratings. The
fluorescence signal was observed to be linear for fluoresceine concentrations between 10-9 and 10-3 M.
Several microfluidic platforms incorporating cavities and channels have been designed and fabricated in silicon and fused silica. C4F8 and SF6 plasmas are used to etch reproducibly 400 μm features in silicon and 150 μm in fused silica. Hydrophilic surface characteristics allow capillary action without external pumping or electro-osmosis. Filling of poled cavities can be triggered by increasing temperature i.e. by tuning hydrophobicity of a channel. The pole structure can also be used for sieving particles of different size or elasticity. In this work, agarose beads trapped by poles were used for solid phase extraction. By covering the microfluidic features, filling is also achieved by cooling the substrate. Filling velocities of aqueous solutions have been observed to depend strongly on liquid composition, but also final treatment and roughness of silicon or silica surface. Mixing of two aqueous solutions can also be triggered by increasing temperature. Cavities with pre-immobilised substance can be filled simultaneously or, if necessary, sequentially. Various non-leaking 3D channel networks can be constructed by gluing, fusion or anodic bonding of many silicon or glass wafers including via holes. Integrating of electrical circuits for both silicon and silica is possible by standard IC technology.
Heated liquid cavities have been studied. Microlitre scale liquid cavities were etched to the surface of a silicon wafer. Liquid cavities were sealed with a glass cover. Integration of active components to the silicon support is also possible. A heater and a thermistor element are integrated into the silicon support. A pole structure was used within the wells for thermal optimization and self-feeding. The pole structure increases the surface area between silicon and liquid, which enhances thermal transport between silicon and liquid. The temperature of the water is also more uniform. The pole structure also makes the liquid cavity semiporous, enabling the self-feeding of samples due to capillary force. Active silicon support could be used in diagnostics and in biotechnology. Silicon supports were tested in PCR (Polymerace Chain Reaction). The construction of the temperature controlling setup for the silicon support is described. Temperature controlling setup is an independent measuring setup. Interface to the silicon support is made with a printed board to a microscope glass slide format. It is possible to use the printed board interface in a microarray reader. The contruction of a fluorescence measurement setup based on a microarray reader is described.
KEYWORDS: Fluorescence resonance energy transfer, Luminescence, Glasses, Europium, Proteins, Photomultipliers, Energy transfer, Time resolved spectroscopy, Time metrology, Solids
Analytical systems based on immunochemistry are largely used in medical diagnostics and in biotechnology. There is a significant pressure to develop the present assay formats to become easier to use, faster, and less reagent consuming. Further developments towards high density array--like multianalyte measurement systems would be valuable. To this aim we have studied the applicability of fluorescence resonance energy transfer and time-resolved fluorescence resonance energy transfer in immunoassays on microspots and in microwells. We have used engineered recombinant antibodies detecting the pentameric protein CRP as a model analyte system, and tested different assay formats. We describe also the construction of a time-resolved scanning epifluorometer with which we could measure the FRET interaction between the slow fluorescence decay from europium chelates and its energy transfer to the rapidly decaying fluorophore Cy5.
A multilayer capillary fiber was designed for optical sensor applications and its optical properties were evaluated by using a fluorescent layer immobilized on its inner surface. This fiber structure combines a large interaction surface (the inner wall of the capillary fiber) for binding of fluorescent indicators with evanescent wave fluorescence measurement, which may facilitate the design of pseudohomogeneous assays without separation of the bound from nonbound fluorescent indicator. The inner surface of the capillary was derivatized by aminosilanization, followed by biotinylation and addition of streptavidin. This biotin- streptavidin coating facilities subsequent immobilization of any biotinylated species (e.g. antibodies, antigens, etc.) participating in specific molecular recognition. We have evaluated some properties of this capillary fiber design by using fluorescent proteins immobilized on the inner wall of capillary by biotin-avidin-interaction. Fluorescence was excited by a HeNe-laser (fluorescent indicator APC; (lambda) em equals 660 nm) and by a Ar-laser (fluorescent indicator RPE, (lambda) em equals 578 nm), and measured with a spectrum analyzer.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.