We present the results of characterization measurements on a 1280 pixel superconducting bolometer array designed for operation at wavelengths around 450 μm. The array is a prototype for the sub-arrays which will form the focal plane for the SCUBA-2 sub-mm camera, being built for the James Clerk Maxwell Telescope (JCMT) in Hawaii. With over 10 000 pixels in total, it will provide a huge improvement in both sensitivity and mapping speed over existing instruments. The array consists of molybdenum-copper bi-layer TES (transition edge sensor) pixels, bonded to a multiplexer. The detectors operate at a
temperature of approximately 175 mK, and require a heat sink at a temperature of approximately 60 mK. In contrast to previous TES arrays, the multiplexing elements are located beneath each pixel (an "in-focal plane" configuration). We present the results of electrical and optical measurements, and show that the optical NEP (noise equivalent power) is less than 1.4 × 10-16 W Hz-0.5 and thus within the goal of 1.5 × 10-16 W Hz-0.5.
The Astronomical Instrumentation Group at University of Cardiff is
already a UK center for submillimetre bolometric detector testing.
The next generation of submillimetre astronomical instrumentation
will incorporate arrays of transition-edge sensor (TES)
bolometers. With the recently expanded facilities and personnel,
the University of Cardiff is poised to become a UK centre for TES
development and testing. We have undertaken a coordinated
programme to develop TES simulation and test capabilities. One
aspect of the programme is to address the problem of saturation of
TES bolometers at high optical loads. We have developed a
"tunable-G" device, which can vary its thermal conductance
whilst in operation. For infrastructure, several sub-Kelvin
cryogenic testbeds have been specifically designed to suit the
requirements of testing submillimetre TES development bolometers.
A description of our tunable-G device to solve the optical
saturation problem will be given along with a description of the
test facilities available at Cardiff.
We report test results for a single pixel antenna-coupled bolometric detector. Our device consists of a dual slot microstrip antenna coupled to an Al/Ti/Au voltage-biased transition edge superconducting bolometer (TES). The coupling architecture involves propagating the signal along superconducting microstrip lines and terminating the lines at a normal metal resistor colocated with a TES on a thermally isolated island. The device, which is inherently polarization sensitive, is optimized for 140 GHz band measurements. In the thermal bandwidth of the TES, we measure a noise equivalent power of 2.0 × 10-17 W/√Hz in dark tests that agrees with calculated NEP including only contributions from thermal, Johnson and amplifier noise. We do not measure any excess noise at frequencies between 1 and 200 Hz. We measure a thermal conductance G ~5.5 × 10-11 W/K. We measure a thermal time constant as low as 437μs at 3μV bias when stimulating the TES directly using an LED.
We present a design for multipixel, multiband submillimeter instrument: SAMBA (Superconducting Antenna-coupled, Multi-frequency, Bolometric Array). SAMBA uses antenna coupled bolometers and microstrip filters. The concept allows for a much more compact, multiband imager compared to a comparable feedhorn-coupled bolometric system. SAMBA incorporates an array of slot antennas, superconducting transmission lines, a wide band multiplexer and superconducting transition edge bolometers. The transition-edge film measures the millimeter-wave power deposited in the resistor that terminates the transmission line.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.