This paper discusses research to develop ultrasonic methods for materials characterization of an innovative new material known as Reactive Powder Concrete (RPC). Also known as Ultra-high performance concrete (UHPC), this relatively new material has been proposed for the construction of civil structures. UHPC mix designs typically include no aggregates larger than sand, and include steel fibers 0.2 mm in diameter and 12 mm in length. These steel fibers increase the strength and toughness of the UHPC significantly relative to more traditional concretes. Compressive strengths of 200 to 800 MPa have been achieved with UHPC, compared with maximum compressive strength of 50 to 100 MPa for more traditional concrete materials. Young’s modulus of 50 to 60 GPa are common for UHPC. However, the curing methods employed have a significant influence on the strength and modulus of UHPC. This paper reports on the development of ultrasonic methods for monitoring the elastic properties of UHPC under a series of curing scenarios. Ultrasonic velocity measurements are used to estimate the bulk elastic modulus of UHPC and results are compared with traditional, destructive methods. Measurements of shear moduli and Poisson's ratio based on ultrasonic velocity are also reported. The potential for the development of quality control techniques for the future implementation of UHPC is discussed.
Reliable health monitoring, including nondestructive evaluation, is an essential part of the feedback and monitoring system for infrastructures. The goal of this paper is to provide a summary of recent research activities that will act as a catalyst to expand interest in the development of new health monitoring technologies. The paper describes the motivation for developing innovative tools for monitoring the health of the nation's infrastructure. An overview of initiatives sponsored by the National Science Foundation to develop new technologies is presented. The paper includes a review of state-of-the-art stress-wave methods for the evaluation of structural materials and pavements at National Institute of Standards and Technology. Finally, efforts at the Federal Highway Administration to develop new technologies for the assessment of the nearly 500,000 bridges along the nation's roads and highways are described.
The NDE Validation Center is a national resource for the independent and quantitative evaluation of existing and emerging NDE techniques. The resources of the NDE Validation Center are available to federal and state agencies, the academic community, and industry. The NDE Validation Center is designed to perform critical evaluations of NDE technologies and to provide a source of information and guidance to users and developers of NDE systems. This paper describes the resources available at the Center and the initial efforts to validate the visual inspection of highway bridges. Efforts to evaluate various NDE methods for the inspection of bridge hanger pins are also described.
This paper describes the evaluation and improvement of a Dual Band Infrared (DBIR) thermal imaging system developed by Lawrence Livermore National Laboratory (LLNL), under the sponsorship of Federal Highway Administration (FHWA). DBIR thermal imaging system is a nondestructive evaluation technique which has the potential of detecting delaminations in concrete bridge decks, with and without asphalt overlays. The system consist of two infrared scanners, one operating at a wavelength of 3 - 5 micrometer and the other at a wavelength of 8 - 12 micrometers. The scanners are mounted in front of a vehicle and are microprocessor controlled from inside the vehicle. The vehicle is driven at a speed of 40 km/hr and a typical bridge deck can be scanned in less than 5 minutes, with a low level of traffic control.
Conference Committee Involvement (12)
Nondestructive Characterization for Composite Materials, Aerospace Engineering, Civil Infrastructure, and Homeland Security III
9 March 2009 | San Diego, California, United States
Nondestructive Characterization for Composite Materials, Aerospace Engineering, Civil Infrastructure, and Homeland Security II
11 March 2008 | San Diego, California, United States
Nondestructive Characterization for Composite Materials, Aerospace Engineering, Civil Infrastructure, and Homeland Security
20 March 2007 | San Diego, California, United States
Nondestructive Detection and Measurement for Homeland Security III
7 March 2005 | San Diego, CA, United States
Nondestructive Evaluation for Health Monitoring and Diagnostics
6 March 2005 | San Diego, United States
Nondestructive Detection and Measurement for Homeland Security II
17 March 2004 | San Diego, CA, United States
Sensors and Smart Structures Technologies for Civil, Mechanical, and Aerospace Systems
15 March 2004 | San Diego, CA, United States
NDE for Health Monitoring and Diagnostics
14 March 2004 | San Diego, United States
Nondestructive Detection and Measurement for Homeland Security
4 March 2003 | San Diego, California, United States
Smart Systems and Nondestructive Evaluation for Civil Infrastructures
3 March 2003 | San Diego, California, United States
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.