A bidirectional optical subassembly comprised of a 2.5 Gbps distributed feedback (DFB) laser diode (LD) directly modulated laser transmitter and a 10 Gbps positive intrinsic negative photodiode receiver was developed for an optical network unit of a 10 Gbps passive optical network. Here, a low-cost mini-dual-in-line package was modified to contain whole components of a transmitter and receiver in a single space while satisfying the requirements of 10 Gbps micro-device package standards. The transmitter was fabricated to achieve high optical output power by placing a micro aspheric lens very close to the DFB LD and reducing the thermal resistance between an LD chip and heat sink to bring down the DFB LD chip temperature. As a result, the transmitter output power was 3.5 dB higher than a conventional transistor outline can BOSA due to a high optical coupling efficiency of more than 70% and a low thermal resistance for heat dissipation. The receiver sensitivity was −21 dBm at a bit error rate of 10−3 and the sensitivity penalty of the receiver due to signal crosstalk was less than 0.3 dB.
A novel 10-Gbps bidirectional optical subassembly (BOSA) comprised of a 1577 nm electroabsorptive modulated laser (EML) transmitter optical subassembly (TOSA) and 1270 nm avalanche photodiode (APD) receiver optical subassembly (ROSA) was developed. Here, a 10-Gbps microdevice compatible two-window flat package was proposed to simplify the EML BOSA structure, considering both the mechanical reliability and cooling performance. As a result, an optical output power of 8 dBm was obtained due to a high optical coupling efficiency of 60%, an extinction ratio of 7 dB, and a dispersion penalty at 20 km transmission of less than 1.5 dB for the EML TOSA. The APD ROSA sensitivity was -21.5 dBm at a bit error rate (BER) of 10−12 and -27 dBm at a BER of 10−3 without forward error correction. In addition, the sensitivity penalty of the APD ROSA due to signal crosstalk was less than 1.2 dB.
We propose a new simple structure-based color combiner with red, green, and blue (RGB) laser diodes (LDs) and a thermally expanded core (TEC) fiber waveguide. As the color combiner used the LDs as optical sources, the total volume of the color combiner could be minimized as 3.84 cc and the output powers of RGB optical sources in the color combiner could be obtained efficiently as 10.324, 13.290, and 10.150 mW, respectively. A TEC fiber waveguide was used as a medium for color combination of RGB in the color combiner. As the TEC fiber waveguide was used as a key component for color combination, we could observe the color combiner had the degree of uniformity and the matching accuracy was good. The measured degree of uniformity and matching accuracy of RGB beams were 121 μm (in large diameter), 56 μm (in small diameter), and 109 μm (on x-axis), 20 μm (on y-axis), respectively.
A compact bidirectional optical subassembly (BOSA) for a 1.25/10-Gbps passive optical network is developed. A vertically stacked 1.25-Gbps transmitter based on a silicon optical bench, and a 10-Gbps receiver based on a low temperature cofired ceramic are implemented to realize low-cost manufacturing and miniaturization for single package application. The proposed BOSA delivers an extinction ratio more than 10 dB at 1.25-Gbps modulation, optical output coupling efficiency is more than 60%, rise and fall time is under 300 ps, and the side mode suppression ratio is more than 35 dB for the transmitter part. For the receiver part, responsivity is more than 0.6 A/W, and sensitivity is lower than -17 dBm at a 10-Gbps bit error rate 10-12 and -21 dBm at BER 10-3 without forward error correction. The cross talk between receiver and transmitter is less than -53 dB up to 10 GHz, and optical isolation is 33 dB.
We propose and demonstrate a novel approach to identify linear and nonlinear propagation regimes of an optical signal in an optical fiber link by using chaos analysis. We show that the chaotic characteristics of a propagating optical signal are affected by both the chromatic dispersion and the nonlinear effects in the optical fiber. Linear or nonlinear behavior is detected by determining the maximum Lyapunov exponent of the signal and the use of the recurrence plot technique. An experimental demonstration is performed using 10-Gbps signal propagation in a 100-km fiber link with different launched optical powers. Chaos analysis shows a clear identification of the linear and nonlinear optical propagation regimes by using a classification scheme based on a multilayer neural network. Numerical simulations confirm the experimental results.
Simultaneous transmission of 2.5-Gb/s baseband and 5.8-GHz-band radio frequency (RF) signals on a single wavelength via a fiber link is successfully demonstrated using the optical diplexer and the newly designed novel baseband/RF mixed-signal multiplexer (MUX) with no mixer. The bit error rate (BER) <10−12 of the baseband signal is maintained when the RF input power is less than −14 dBm after 10-km-long distance transmission. The maximum carrier-to-noise ratio (CNR) of the RF signal is measured as 23 dB with no additional amplifier. The measured insertion loss for the RF signal of the mixed-signal MUX is 1.2 dB at 5.8 GHz, and the isolations between the two bands are about 20 dB for the baseband and 30 dB for the RF band, respectively.
We demonstrate a highly efficient in-fiber out-coupling device. The core mode is coupled to the cladding by a tilted fiber Bragg grating and then the cladding mode is out-coupled from the optical fiber through V-grooved cladding. The light emitting characteristics are investigated experimentally and a maximum out-coupling efficiency of 54.8% is obtained.
The effect of external feedback on an isolator free transmitter was investigated experimentally by measuring relative intensity noise (RIN). The experiments were done under the possible conditions that might happen during operation such as external reflection and temperature change. In addition to that, the effect of reflection depending on the types of source which DFB and FP LD are widely used for that. Finally, LD to Fiber alignment under external reflection was demonstrated. It was found that the effect of external reflection was dominant factor compared with temperature change and FP LD is less affected by reflection than DFB LD. The maximum RIN occurs at the maximum coupling position of LD and fiber and the minimum RIN exists near the maximum coupling position, which can be used to optimize the coupling and RIN tolerance according to the alignment position by changing the lens focal length.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.