This paper designs and implements one kind of automatic mode-locked system. It can adjust a passively mode-locked
fiber laser to keep steady mode-locked states automatically. So the unsteadiness of traditional passively mode-locked
fiber laser can be avoided. The system transforms optical signals into electrical pulse signals and sends them into MCU
after processing. MCU calculates the frequency of the signals and judges the state of the output based on a quick
judgment algorithm. A high-speed comparator is used to check the signals and the comparison voltage can be adjusted to
improve the measuring accuracy. Then by controlling two polarization controllers at an angle of 45degrees to each other,
MCU extrudes the optical fibers to change the polarization until it gets proper mode-locked output. So the system can
continuously monitor the output signal and get it back to mode-locked states quickly and automatically. States of the
system can be displayed on the LCD and PC. The parameters of the steady mode-locked states can be stored into an
EEPROM so that the system will get into mode-locked states immediately next time. Actual experiments showed that,
for a 6.238MHz passively mode-locked fiber lasers, the system can get into steady mode-locked states automatically in
less than 90s after starting the system. The expected lock time can be reduced to less than 20s after follow up
improvements.
A high-resolution, real-time range imaging system based on a LED array phase-shift range finder was developed to measure three-dimensional surface profiles. The range image is captured by a time-division scanning LED array heterodyne phase-shift range finder. The phase measurement used for obtaining depth is implemented by using the fast "four-bucket" algorithm. The design of a fast automatic gain control circuit obviously reduces the feedback response time and improves system measurement speed. Experimental tests for evaluation of the imaging system performance are described. Based on the theoretical analysis, a simplified signal-to-noise ratio model is proposed for guiding the design of this imaging system. Last, some issues requiring attention on constructing a large-pixel version of the system are also discussed. It was found that the range images can be acquired at a rate of 10 frames per second with a depth resolution better than ±5 mm in the range of 50 to 1000 mm.
KEYWORDS: Modulation, Vertical cavity surface emitting lasers, Signal processing, Ranging, Laser range finders, Phase shift keying, Digital signal processing, Analog electronics, Distortion, Complex systems
The paper proposes a small modulation and high precision laser range finder using the self-mixing effect in a
single-mode vertical-cavity surface-emitting laser (VCSEL). According to the characteristic curve of single-mode
VCSEL, the nonlinear distortion of Δλ/ΔI is severe and related with the modulation current ΔI, which worsens the system
ranging accuracy obviously. In this paper, by applying small current to modulate single-mode VCSEL and specific
circuits to process photoelectric signal, the system ranging accuracy is improved obviously. The experiment results show
that, using small modulation current ΔI= 0.28 mAp-p, modulation frequency fm = 500 Hz to modulate single-mode
VCSEL, and applying difference frequency analog phase-locked loop (APLL) to process the self-mixing beat frequency
signals that exist phase abrupt changes, when the sampling time is 0.1 s, the measurement dynamic range is as large as 50
~ 500 mm, and the ranging accuracy is better than 2 mm.
A new, compact laser Doppler velocimetry is proposed, which is composed of a single-mode vertical-cavity surface-emitting laser modulated by a dynamical triangular current and a collimating lens. It can indicate the direction of velocity without ambiguity in the wide dynamic range of 5.2mm/s to 479.9mm/s when the sampling time is 0.1 second in the measurement. The accuracy of velocity measurement is better than 3.1% in the whole velocity range. What's more, this LDV works very well on different diffusing surfaces, even on a black glossy photographic paper.
This paper presents a theoretical and numerical analysis of polarization properties used as Doppler velocimetry in Vertical-Cavity Surface-Emitting lasers. A good match is found between numerical results and reported experiment results. We show that condition of generating square waves is the VCSELs must operated inside the bistable region and frequency difference between two linear polarization modes is equal to several certain values. We can select proper VCSELs which frequency difference between two linear polarization modes is multiple of ±3G to obtain asymmetric waveform of self-mixing signal.
SM-LDV (Self-Mixing Type Laser Doppler Velocimeter) using single mode VCSEL (Vertical Cavity Surface Emitting Lasers) has many characteristic such as high accuracy of velocity measurement, low power dissipation and low cost. The saw-tooth waveform of Doppler signal can be used to discriminate the motion direction. Because of low light power of single mode VCSEL, the backscattered light is so weak that the saw-tooth waveform is not good enough to discriminate the motion direction. SM-LDV direction discrimination using single mode VCSEL modulated by triangular wave is not obviously dependent on the light power of Laser and its reliability is better. The dynamic range is very narrow when the VCSEL is modulated by constant frequency triangular wave. We present a method that VCSEL is modulated by triangular wave whose frequency is tracking the divided frequency of Doppler frequency shift (fD) and it can expand the dynamic range more than one order of magnitude. The results show that the dynamic range of direction discrimination can reach 5-500mm/s when the wavelength of single mode VCSEL is 850nm and the operating current is 8.6mA, the frequency of triangular wave is fD/16,the modulation current of triangular wave is 0.042mA.
The experiments show that the single-mode vertical-cavity surface-emitting laser (VCSEL) Laser Doppler Velocimetry (LDV) is better than the multilongitudinal-mode laser diode LDV in many characteristics, such as the accuracy of velocity measurement and the temperature range of the laser. Because the output power of the single-mode VCSEL is very low and only 0.7mW, the backscattered light received by the photodiode in the laser house is so weak that the signal-to-noise ratio (SNR) of Doppler signal is low. And the Doppler signal spectrum width spread and amplitude modulation envelope badly influence the velocity measurement accuracy. Analog phase-locked loop (PLL) has many characteristics, such as narrow band tracking filter, locking the signal with peak voltage and high rejection ratio of amplitude modulation. Using the analog PLL, the SNR of Doppler signal and the velocity measurement accuracy can be improved obviously. But because the locking range of the common analog PLL is narrow, we use difference frequency analog PLL to expand the locking range, and the dynamic range of velocity measurement can be greatly expanded. As a result, the velocity measurement accuracy of the single-mode VCSEL self-mixing LDV is better than 1% when the velocity range is from 30mm/s to 480mm/s.
The phase distribution design process of the pure phase element (PPE) used for quasi-annular beam shaping is introduced in this paper. A new optimization algorithm named Quasi-Gradient Descent (Quasi-GD) algorithm has been developed and used here to meet such design requirement. With a more restrictive sampling mode named precise sampling in the optimization, the simulated result shows that the uniformity of energy distribution on the focal plane is invariant with different sampling intervals and the true beam shaping effect is achieved.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.