CEA aims at developing a compact 1550 nm Frequency Modulated Continuous Wave (FMCW) LiDAR on chip. In this paper, individual demonstrators, corresponding to three main components of a LiDAR (Light Distance And Ranging) system, are combined in a test bench: a FMCW laser source, an emission and reception Optical Phased Array (OPA) and an optical heterodyne detection module. Each component has been individually tested, but also evaluated in order to derive the system performance of a complete LiDAR. A test platform has been developed to calibrate an OPA fabricated at CEA platform, either in emission or in reception mode. The tested OPA includes 256 channels based on grating antennae, with 1.5 μm pitch and 256 thermo-optic phase shifters. More recently, this platform has been completed with a FMCW interferometer, where the FMCW LiDAR detection can be evaluated through a mixed propagation setup, composed of optical fibers and free space. Then, the OPA may be inserted into this setup. Therefore, the optical fiber FMCW interferometer has been optimized to detect the lowest signal (typically less than one hundred fW) and to estimate the signal-to-noise ratio (up to almost 30 dB) with low noise photodiodes. Performance has been compared to theoretical predictions. Then, our custom OPA is included inside this experimental setup in a free space propagation environment. The performance measurements extracted from the spectral analysis are in agreement with the expectations.
An Optical Phased Array (OPA) is similar to a one dimensional (1D) dynamic diffraction array. The phase law of the emitters is numerically programmable and enables to form a beam, that point towards a targeted direction. OPAs have a high potential for a new generation of LiDAR (Light Detection and Ranging) systems, since they avoid mechanical beam scanning. For the development of such LiDAR, many characterizations are essential to optimize the OPA and to get a full control of their performance. To carry out these tests, CEA-Leti has developed a modular optical bench designed to characterize large scale 1D-OPAs in free space. This bench allows beam-forming calibration at various angles thanks to an optical setup based on far-field imaging in the Fourier plane. This set up directly analyses a field of view of 22° (-11°/+11°) and can rotate in the azimuthal plane of the OPA to cover angles ranging from -50° to +50°. The OPA board is mounted on an additional rotation stage to match the OPA beam output with the beam forming set-up optical axis. For practical use, the optical axis is parallel to the floor (i.e. to the optical table). Moreover, after calibration, additional options allow to switch the setup for practical operations, as the OPA use in real space, e.g. for aiming at a target. A Peltier and a regulation loop allow testing the OPA at various temperatures. Fast photodiodes have been implemented to measure the switching time between distinct angular positions. In this paper, we report data acquired with this setup on a 256 channels OPA operating at @1550 nm, that is based on grating antennas with 1.5 μm pitch and thermo-optic phase shifters.
I. Robin, P. Ferret, A. Dussaigne, C. Bougerol, D. Salomon, X. Chen, M. Charles, P. Tchoulfian, A. Gasse, A. Lagrange, M. Consonni, H. Bono, F. Levy, Y. Desieres, A. Aitmani, S. Makram-Matta, E. Bialic, P. Gorrochategui, L. Mendizabal
With a long experience in optoelectronics, CEA-LETI has focused on Light Emitting Diode (LED) lighting since 2006. Today, all the technical challenges in the implementation of GaN LED based solid state lighting (SSL) are addressed at CEA-LETI who is now an RandD player throughout the entire value chain of LED lighting. The SSL Line at CEA-LETI first deals with the simulation of the active structures and LED devices. Then the growth is addressed in particular 2D growth on 200 mm silicon substrates. Then, technological steps are developed for the fabrication of LED dies with innovative architectures. For instance, Versatile LED Array Devices are currently being developed with a dedicated μLED technology. The objective in this case is to achieve monolithical LED arrays reported and interconnected through a silicon submount. In addition to the required bonding and 3D integration technologies, new solutions for LED chip packaging, thermal management of LED lamps and luminaires are also addressed. LETI is also active in Smart Lighting concepts which offer the possibility of new application fields for SSL technologies. An example is the recent development at CEA LETI of Visible Light Communication Technology also called LiFi. With this technology, we demonstrated a transmission rate up to 10 Mb/s and real time HD-Video transmission.
LED reliability and lifetime prediction is a key point for Solid State Lighting adoption. For this purpose, one hundred and fifty LEDs have been aged for a reliability analysis. LEDs have been grouped following nine current-temperature stress conditions. Stress driving current was fixed between 350mA and 1A and ambient temperature between 85C and 120°C. Using integrating sphere and I(V) measurements, a cross study of the evolution of electrical and optical characteristics has been done. Results show two main failure mechanisms regarding lumen maintenance. The first one is the typically observed lumen depreciation and the second one is a much more quicker depreciation related to an increase of the leakage and non radiative currents. Models of the typical lumen depreciation and leakage resistance depreciation have been made using electrical and optical measurements during the aging tests. The combination of those models allows a new method toward a quicker LED lifetime prediction. These two models have been used for lifetime predictions for LEDs.
This paper reports simulation results of transmission performances after introduction of DFB laser diode parameters variations versus time extrapolated from accelerated tests. Simulations are performed using a system simulator to study the consequence of degradations of the laser diode on system performances (eye diagram, quality factor - Q and binary error rate - BER). The studied link consists in 4x2.5 Gbits/s WDM channels with direct modulation and equally spaced by 0,8 nm around the 1550 nm central wavelength. In this paper, only one channel is assumed to be degraded considering an only one activation energy. Simulation results clearly show that variation of basic parameters such as bias current or central wavelength induces a penalization of dynamic performances of the complete WDM link. Consequences on adjacent channels are pointed out underlying the relation between the variations of eye diagram parameters (height, noise, cross-talk, jitter) and the Q-factor decrease. Variations of optical spectrum density at the output of the demultiplexer are also analyzed showing penalties on the final cross-talk. Different degradation kinetics of aged laser diodes from a same batch have been also implemented to build the final distribution of Q-factor and BER after 25 years finally demonstrating the low impact of such variations. The strong interest of this approach is to evaluate the robustness of a dedicated-technology and to become a complementary tool of actual reliability-testing methods and physics of failure in the context of new reliability modeling approach. We have also highlighted the relevance of failure criteria established by actual qualification standards for high-rate optical telecommunication systems.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.