Xtend is one of the two telescopes onboard the X-ray imaging and spectroscopy mission (XRISM), which was launched on September 7th, 2023. Xtend comprises the Soft X-ray Imager (SXI), an X-ray CCD camera, and the X-ray Mirror Assembly (XMA), a thin-foil-nested conically approximated Wolter-I optics. A large field of view of 38′ × 38′ over the energy range from 0.4 to 13 keV is realized by the combination of the SXI and XMA with a focal length of 5.6 m. The SXI employs four P-channel, back-illuminated type CCDs with a thick depletion layer of 200 μm. The four CCD chips are arranged in a 2×2 grid and cooled down to −110°C with a single-stage Stirling cooler. Before the launch of XRISM, we conducted a month-long spacecraft thermal vacuum test. The performance verification of the SXI was successfully carried out in a course of multiple thermal cycles of the spacecraft. About a month after the launch of XRISM, the SXI was carefully activated and the soundness of its functionality was checked by a step-by-step process. Commissioning observations followed the initial operation. We here present pre- and post-launch results verifying the Xtend performance. All the in-orbit performances are consistent with those measured on ground and satisfy the mission requirement. Extensive calibration studies are ongoing.
We have developed a novel x-ray interferometer, multi-image x-ray interferometer module (MIXIM), comprised of a fine aperture mask and an x-ray detector. The angular resolution of this system can be improved with an increase of the distance between two components or a decrease of the aperture size. Although MIXIM has already achieved an angular resolution of less than 0.1” by applying the Talbot effect with a periodic multi-pinhole mask, there remains the issue that its low opening fraction of 1.3% decreases the effective area of the imaging system. Therefore, we newly introduced periodic coded aperture masks which have opening fractions of about 50% instead of the multi-pinhole mask. Conducting an experiment with a 12.4 keV parallel x-ray beam, we successfully demonstrated that the periodic coded aperture could form the self-image, and obtained the x-ray source profile with sub-arcsecond angular resolution by deciphering the coded pattern. The effective area increases about 25 times compared with the multi-pinhole mask by the introduction of the periodic coded aperture masks, which indicates that this novel method can be effective for addressing the problem.
We intoduce our novel method of super high resolution astronomical X-ray imaging, Multi Image X-ray Interferometer Method, Modules, Missions (MIXIM). In series of experiments on the ground we not only verified the concept of MIXIM but also realized 2D imaging with angular resolution better than 0. ′′1. Employment of small pixel size CMOS sensor was the key to this achievement. Scalability is also an important feature of MIXIM., and various mission format is available. We show some examples from a very small satellite for sub arcsecond resolution to a formation flight with a millions km separation to gain µas resolution. MIXIM is different from X-ray mirrors in various points, for example, it does not have a collecting power. Considering the limitations and advantages of MIXIM, we should choose bright apparently point-like sources as targets. Nearby AGNs are primary ones, and the MIXIM scope just corresponds to spatial scales which have not yet resolved in X-rays.
CFRP is a composite material composed of carbon fiber and resin. CFRP is commonly applied to the aerospace industry which requires lightweight and intensity. Thanks to superior formability of CFRP, we can form shape of Wolter-1 optics, which consists of paraboloid and hyperboloid, to a monolithic substrate. Since the surface roughness of a CFRP substrate is a few µm, we have to make the smooth surface for reflecting X-rays on the CFRP substrate. We have developed a new method of shaping the reflective surface instead of the replica method used in lightweight X-ray mirrors such as Astro-H. In the new method, the reflective surface is formed by pasting thin sheet-glasses with 100 µm thick onto the CFRP substrate. The thin sheet-glass has a surface roughness about 0.4 nm as measured by Zygo. We fabricated a CFRP mirror pasting thin sheet-glasses, and then coated tungsten on the mirror in June 2020. The figure error (s) of the CFRP mirror was achieved to be about 1-2 μm by stacking the CFRP mirror on the housing module. X-ray imaging quality of the CFRP mirror was measured at Spring-8 in July 2020. The half-power diameter of the CFRP mirror was estimated to be about 150 arcsec, which was nearly equal to the prediction from a distribution of the slope error deduced from the surface profile. We describe a future plan to improve the image quality of the CFRP mirror.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.