Mod-Cam is a first light and commissioning instrument for the CCAT-prime project’s six-meter aperture Fred Young Submillimeter Telescope (FYST), currently under construction at 5600 m on Cerro Chajnantor in Chile’s Atacama Desert. Prime-Cam, a first-generation science instrument for FYST, will deliver over ten times greater mapping speed than current and near-term facilities for unprecedented 280–850 GHz broadband and spectroscopic measurements with microwave kinetic inductance detectors (MKIDs). CCAT-prime will address a suite of science goals, from Big Bang cosmology to star formation and galaxy evolution over cosmic time. Mod-Cam deployment on FYST with a 280 GHz instrument module containing MKID arrays is planned for early science observations in 2024. Mod-Cam will be used to test instrument modules for Prime-Cam, which can house up to seven instrument modules. We discuss the design and status of the 0.9 m diameter, 1.8 m long Mod-Cam receiver and 40 cm diameter 280 GHz instrument module, with cold stages at 40 K, 4 K, 1 K, and 100 mK. We also describe the instrument module’s cryogenic readout designs to enable the readout of more than 10,000 MKIDs across 18 networks.
KEYWORDS: Sensors, Resonators, Digital signal processing, Inductance, Data conversion, Multiplexing, Signal to noise ratio, Frequency combs, Signal attenuation
The Prime-Cam instrument on the Fred Young Submillimeter Telescope (FYST) is expected to be the largest deployment of millimeter and submillimeter sensitive kinetic inductance detectors to date. To read out these arrays efficiently, a microwave frequency multiplexed readout has been designed to run on the Xilinx Radio Frequency System on a Chip (RFSoC). The RFSoC has dramatically improved every category of size, weight, power, cost, and bandwidth over the previous generation readout systems. We describe a baseline firmware design which can read out four independent RF networks each with 500 MHz of bandwidth and 1000 detectors for ∼30 W. The overall readout architecture is a combination of hardware, gateware/firmware, software, and network design. The requirements of the readout are driven by the 850 GHz instrument module of the seven-module Prime-Cam instrument. These requirements along with other constraints which have led to critical design choices are highlighted. Preliminary measurements of the system phase noise and dynamic range are presented.
The Fred Young Submillimeter Telescope (FYST) at the Cerro-Chajnantor Atacama Telescope prime (CCATprime) Facility will host Prime-Cam as a powerful, first generation camera with imaging polarimeters working at several wavelengths and spectroscopic instruments aimed at intensity mapping during the Epoch of Reionization. Here we introduce the 850 GHz (350 micron) instrument module. This will be the highest frequency module in Prime-Cam and the most novel for astronomical and cosmological surveys, taking full advantage of the atmospheric transparency at the high 5600 meter CCAT-prime siting on Cerro Chajnantor. The 850 GHz module will deploy ∼40,000 Kinetic Inductance Detectors (KIDs) with Silicon platelet feedhorn coupling (both fabricated at NIST), and will provide unprecedented broadband intensity and polarization measurement capabilities. The 850 GHz module will be key to addressing pressing astrophysical questions regarding galaxy formation, Big Bang cosmology, and star formation within our own Galaxy. We present the motivation and overall design for the module, and initial laboratory characterization.
Prime-Cam is a first-generation instrument for the Cerro Chajnantor Atacama Telescope-prime (CCAT-prime) Facility. The 850 GHz module for Prime-Cam will probe the highest frequency of all the instrument modules. We describe the parameter space of the 850 GHz optical system between the Fλ spacing, beam size, pixel sensitivity, and detector count. We present the optimization of an optical design for the 850 GHz instrument module for CCAT-prime. We further describe the development of the cryogenic RF chain design to accommodate 30 readout lines to read 41,400 kinetic inductance detectors (KIDs) within the cryogenic testbed.
The Epoch of Reionization Spectrometer (EoR-Spec) is one of the instrument modules to be installed in the Prime-Cam receiver of the Fred Young Submillimeter Telescope (FYST). This six-meter aperture telescope will be built on Cerro Chajnantor in the Atacama Desert in Chile. EoR-Spec is designed to probe early star-forming regions by measuring the [CII] fine-structure lines between redshift z = 3.5 and z = 8 using the line intensity mapping technique. The module is equipped with a scanning Fabry-Perot interferometer (FPI) to achieve the spectral resolving power of about RP = 100. The FPI consists of two parallel and identical, highly reflective mirrors with a clear aperture of 14 cm, forming a resonating cavity called etalon. The mirrors are silicon based and patterned with double-layer metamaterial anti-reflection coatings (ARC) on one side and metal mesh reflectors on the other. The double-layer ARCs ensure a low reflectance at one substrate surface and help tailor the reflectance profile over the FPI bandwidth. Here we present the design, fabrication processes, test setup, and characterization of silicon mirrors for the FPI.
The Fred Young Submillimeter Telescope (FYST), which is the telescope of the CCAT-prime project, will be located at 5600 m near the summit of Cerro Chajnantor in northern Chile, and will host the modular instrument called Prime-Cam. Two of the instrument modules in Prime-Cam will be a spectrometer with a resolving power of R ∼ 100 and populated with a detector array of several thousand KIDs (Kinetic Inductance Detectors). The main science goal of this spectrometer module, called EoR-Spec, is to probe the Epoch of Reionization (EoR) in the early universe using the Line Intensity Mapping (LIM) technique with the redshifted [CII] fine-structure line. This presentation provides an overview of the optical, mechanical, and spectral design of EoR-Spec, as well as of the detector array that will be used. The optical design consists of four silicon lenses that have anti-reflection metamaterial layers. A scanning Fabry-Perot Interferometer (FPI) will be located at the pupil and provides the spectral resolution over the full spectral coverage of 210 GHz to 420 GHz in two orders, resulting in a redshift coverage of the [CII] line from z = 3.5 to z = 8. The detector array consists of three subarrays of KIDs, two of which are tuned for the frequency range between 210 GHz and 315 GHz, and one that is tuned for the 315 GHz to 420 GHz range. The angular resolution will be between about 30′′ to 50′′. This presentation also addresses the spectral and spatial scanning strategy of EoR-Spec on FYST. EoR-Spec is expected to be installed into Prime-Cam about 1 year after first light of FYST.
The Advanced L-band Phased Array Camera for Astronomy (ALPACA) will be a fully cryogenic phased array feed instrument operating from 1.3-1.7 GHz, providing an unmatched combination of sensitivity, wide bandwidth, and large instantaneous field of view. The instrument was originally targeted for installation at the Arecibo Radio Telescope but the tragic loss of the Gregorian platform in 2020 has led to a proposal to deploy ALPACA at the prime focus of the Green Bank Telescope. Here, we will report on the design and implementation of the antenna array, cryogenic vacuum vessel, signal transport and the digital back end.
HIRMES, SOFIA’s third generation science instrument, delivers spectroscopy at wavelengths between 25 and 122 um and resolving powers (RP) between 600 and 100,000. The detectors arrays are background-limited transition edge sensed bolometers. Here we focus on the development, testing, and performance of the series of 8 tunable cryogenic scanning Fabry-Perot interferometers (FPI) that deliver the imaging (RP = 2000), and the long-slit medium resolution (RP = 10,000) and high resolution (RP = 100,000) spectroscopic modes. The FPIs use free-standing metal meshes mirrors, flexible parallelogram translations stages, PZTs and/or cryomoters for displacement. and capacitive sensors for displacement measure.
The CCAT-prime project's first light array will be deployed in Mod-Cam, a single-module testbed and first light cryostat, on the Fred Young Submillimeter Telescope (FYST) in Chile's high Atacama desert in late 2022. FYST is a six-meter aperture telescope being built on Cerro Chajnantor at an elevation of 5600 meters to observe at millimeter and submillimeter wavelengths.1 Mod-Cam will pave the way for Prime-Cam, the primary first generation instrument, which will house up to seven instrument modules to simultaneously observe the sky and study a diverse set of science goals from monitoring protostars to probing distant galaxy clusters and characterizing the cosmic microwave background (CMB). At least one feedhorn-coupled array of microwave kinetic inductance detectors (MKIDs) centered on 280 GHz will be included in Mod-Cam at first light, with additional instrument modules to be deployed along with Prime-Cam in stages. The first 280 GHz detector array was fabricated by the Quantum Sensors Group at NIST in Boulder, CO and includes 3,456 polarization- sensitive MKIDs. Current mechanical designs allow for up to three hexagonal arrays to be placed in each single instrument module. We present details on this first light detector array, including mechanical designs and cold readout plans, as well as introducing Mod-Cam as both a testbed and predecessor to Prime-Cam.
HIRMES is a far-infrared spectrometer that was chosen as the third generation instrument for NASA's SOFIA airborne observatory. HIRMES promises background limited performance in four modes that cover the wavelength range between 25 and 122 μm. The high-spectral resolution (R ≈105) mode is matched to achieve maximum sensitivity on velocity-resolved lines to study the evolution of protoplanetary disks. The mid-resolution (R≈12,000) mode is suitable for high sensitivity imaging of galactic star formation regions in, for example, the several far-infrared fine structure lines. The low-resolution (R≈2000) imaging mode is optimized for spectroscopic mapping of far-infrared fine structure lines from nearby galaxies, while the low resolution (R≈600) grating spectrometer mode is optimized for detecting dust and ice features in protostellar and protoplanetary disks. Several Transition Edge Sensed (TES) bolometer arrays will provide background limited sensitivity in each of these modes. To optimize performance in the various instrument modes, HIRMES employs eight unique fully-tunable cryogenic Fabry-Perot Interferometers (FPIs) and a grating spectrometer. Here we present the design requirements and the mechanical and optical characteristics and performance of these tunable FPI as well as the control electronics that sets the mirror separation and allows scanning of the FPIs.
CCAT-prime will be a 6-meter aperture telescope operating from sub-mm to mm wavelengths, located at 5600 meters elevation on Cerro Chajnantor in the Atacama Desert in Chile. Its novel crossed-Dragone optical design will deliver a high throughput, wide field of view capable of illuminating much larger arrays of sub-mm and mm detectors than can existing telescopes. We present an overview of the motivation and design of Prime-Cam, a first-light instrument for CCAT-prime. Prime-Cam will house seven instrument modules in a 1.8 meter diameter cryostat, cooled by a dilution refrigerator. The optical elements will consist of silicon lenses, and the instrument modules can be individually optimized for particular science goals. The current design enables both broad- band, dual-polarization measurements and narrow-band, Fabry-Perot spectroscopic imaging using multichroic transition-edge sensor (TES) bolometers operating between 190 and 450 GHz. It also includes broadband kinetic induction detectors (KIDs) operating at 860 GHz. This wide range of frequencies will allow excellent characterization and removal of galactic foregrounds, which will enable precision measurements of the sub-mm and mm sky. Prime-Cam will be used to constrain cosmology via the Sunyaev-Zeldovich effects, map the intensity of [CII] 158 μm emission from the Epoch of Reionization, measure Cosmic Microwave Background polarization and foregrounds, and characterize the star formation history over a wide range of redshifts. More information about CCAT-prime can be found at www.ccatobservatory.org.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.